Hyundai Venue: Hydraulic System / Line Pressure Control Solenoid Valve (LINE_VFS). Repair procedures
| • |
Refer to the DTC manual for the check procedure.
|
|
| • |
When the solenoid valve Diagnostic Trouble Codes (DTC) is on,
perform the following procedure to replace it.
|
| • |
Automatic transaxle is composed of delicate components. Be careful
not to cause any damage on the component in the course of assembly
and disassembly.
|
| • |
Maintain clean condition so that foreign substance does not
get into the automatic transaxle.
|
| • |
Use a coated apron, latex gloves, and stainless tray to prevent
foreign substance from getting into the transaxle.
|
| • |
Automatic transaxle fluid (ATF) can be reused. Collect it using
a clean 10-liter beaker.
|
|
| 1. |
Turn ignition switch OFF and disconnect the negative (-) battery cable.
|
| 2. |
Remove the air cleaner and air duct.
| (1) |
Remove the air duct (A).
|
| (2) |
Disconnect the breather hose (B) and air intake hose (C).
|
| (3) |
Remove the air cleaner assembly (D).
|
Tightening torque :
Hose clamp bolt (C):
2.9 - 4.9 N.m (0.3 - 0.5 kgf.m, 2.1 - 3.6 lb-ft)
Air cleaner assembly bolts (D) :
3.9 - 5.9 N.m (0.4 - 0.6 kgf.m, 2.9 - 4.3 Ib-ft)
|
|
|
| 3. |
Discharge the automatic transaxle fluid (ATF).
(Refer to Automatic Transaxle Syatem - "Automatic Transaxle Fluid (ATF)")
|
| 4. |
Disconnect the wiring fixing clip (A).
|
| 5. |
Disconnect the air bleeder hose (B).
|
| 6. |
Disconnect the ATF cooler hose (A).
| •
|
Be careful not to cause any damage on the hose when
tightening the clamp.
|
| •
|
Mount the clamp tightening part in the designated direction
so that interference does not occur with the adjacent
parts.
|
| •
|
After connecting the hose, check for oil leakage on
the connecting part while the engine is on.
|
|
|
| 7. |
Unscrew the bolts and remove the valve body cover (A).
|
Tightening torque :
11.8 - 13.7 N.m (1.2 - 1.4 kgf.m, 8.7 - 10.1 lb-ft)
|
| •
|
When re-mounting the valve body cover, replace the gasket
with a new one.
|
| •
|
After mounting the valve body cover, check for oil leakage
on the connecting part while the engine is on.
|
|
|
| 8. |
Unscrew the bolts and disconnect the solenoid valve connector (A).
|
| 9. |
Remove the support bracket mounting bolt (A).
|
Tightening torque :
9.8 - 11.8 N.m (1.0 - 1.2 kgf.m, 7.2 - 8.7 lb-ft)
|
|
| 10. |
Remove the support bracket (A).
|
| 11. |
Loosen the bolt (B).
|
Tightening torque :
9.8 - 11.8 N.m (1.0 - 1.2 kgf.m, 7.2 - 8.7 lb-ft)
|
|
| 12. |
Remove the line pressure control solenoid valve (A).
|
| 1. |
To install, reverse the removal procedure.
|
| 2. |
Inject the automatic transaxle oil and inspect the oil level.
(Refer to Automatic Transaxle System - "Automatic Transaxle Fluid (ATF)")
| 1) |
After ATF level check or exchange, be sure to remove
residual ATF on transaxle case.
(Be especially sure to remove residual ATF between automatic
transaxle case and valve body cover)
|
| 2) |
After installing the valve body cover, make sure to
check the oil leakage at the connection area with the
engine ON.
|
|
|
| 3. |
Clear the diagnostic trouble codes (DTC) using the diagnostic tool.
| •
|
Even though disconnecting the battery negative terminal,
the DTCs will not be cleared. So, be sure to clear the
DTCs using the diagnostic tool.
|
|
|
| 4. |
In order to prevent start delay and gear shift shock during acceleration
and start, perform TCM learning after replacing the solenoid valve.
(Refer to Automatic Transaxle Control System - "Repair procedures")
|
Component Location (1)_Valve
Body Cover
1. Valve Body Cover
2. Valve Body Cover Gasket
3. Solenoid Valve Connector
Component Location (2)_Solenoid
Valve
1...
Description
•
35R Clutch control solenoid valve(35R/C) is attached to the valve body.
•
This variable force solenoid valve directly controls the hydraulic pressure
inside the 35R clutch...
Other information:
..
Removal
1.
Remove the fuel pump.
(Refer to Fuel Delivery System - "Fuel Pump")
2.
Disconnect the electric pump wiring connector (A) and the fuel sender
connector (B)...
Categories
WARNING
To reduce the risk of an air bag deploying unexpectedly and causing serious
injury or death:
Do not hit or allow any objects to impact the locations where air bags
or sensors are installed.
Do not perform maintenance on or around the air bag sensors. If the location
or angle of the sensors is altered, the air bags may deploy when they should
not or may not deploy when they should.
Do not install bumper guards or replace the bumper with a nongenuine
HYUNDAI parts. This may adversely affect the collision and air bag deployment
performance.
Place the ignition switch in the LOCK/OFF or ACC position when the vehicle
is being towed to prevent inadvertent air bag deployment.
Have all air bag repairs conducted by an authorized HYUNDAI dealer.
read more
Line Pressure Control Solenoid Valve (LINE_VFS). Components and components location
35R Clutch Control Solenoid Valve (35R/C_VFS). Description and operation