Hyundai Venue: Tire Pressure Monitoring System / Description and operation
The Tire Pressure Monitoring System (TPMS) monitors the pressure and temperature
inside the tire in order to warn the driver of changes in pressure which may
influence the operation of the vehicle. The TPMS control module analyzes wireless
information fro
In other words, the system detects the pneumatic pressure of the tires and warns
the driver of if the pneumatic pressure drops below the standard level.
Low-pressure Warning Lamp on the Dashboard
Dashboard tire low-pressure warning light
Lamp ON/OFF Conditions when the Tire Pressure Decreases or Air is Leaking from
the Tire
1. |
Lamp ON
• |
The lamp turns ON when the tire pressure decreases below the
standard level.
|
|
2. |
Lamp OFF
• |
Low pneumatic pressure: The warning lamp turns OFF when the
tire pressure exceeds the pressure required to turn off the
lamp.
|
|
TPMS Fault Warning Lamp
1. |
Warning Conditions and Display
• |
When the system detects a defect in the external operating environment
(low battery voltage, abnormal vehicle speed, etc), the warning
lamp blinks for about 1 minute and then turns ON.
|
|
2. |
Lamp OFF
• |
The warning lamp turns OFF when the DTC is resolved. The DTC
is automatically resolved when the system does not receive any
fault signals for 30 or more ignition cycles after it changes
to the previous fault code.
|
•
|
If this phenomenon occurs while driving, you should
check the cause of the fault even after the DTC is resolved.
(Turn the ignition switch from OFF to ON. Then, check
the lamp status.)
|
•
|
The warning lamp turns off once the DTC is resolved.
The warning lamp stays on until you complete the check
necessary to resolve the DTC.
|
•
|
If the DTC is resolved, the warning lamp turns OFF during
the same ignition cycle.
|
|
If the vehicle starts within 19 minutes after the replacement
of the wheel of the stopped vehicle, the TPMS Malfunction Indicator
on the instrument cluster illuminates.
–
|
The above symptom is due to communication failure between
the IBU and the replaced TPMS ID.
|
–
|
This communication failure indicator turns off in 19
minutes after the vehicle stops through the IBU’s automatic
learning process of TPMS ID.
(When driving the vehicle after stopping for over 19
minutes, the indicator turns off automatically.)
|
|
|
System Defect
1. |
General Operation
• |
The system detects many input elements to identify potential
defects.
|
• |
The priority of a defect depends on its cause.
|
• |
Certain defects are not diagnosed as DTCs.
|
The following are major defects:
• |
In order to diagnose more symptoms of the fault when the ignition
line malfunctions, you must check the warning lamp when you
turn the ignition on.
|
• |
Check whether the warning lamp turns on and then off.
|
|
Components
1. Integrated Body Control Unit
(IBU)
2. TPMS sensor (FL)
3. TPMS sensor (RL)
4. TPMS sensor (RR)
5...
TPMS Inspection method
Inspection
•
Find the inspection number by referring to the table above...
Other information:
System setting
The driver can activate the system by placing the ignition switch to the
ON position and by selecting “User Settings → Driver Assistance → Parking Safety
→ Rear Cross-Traffic Safety”. RCCW turns on when ‘Rear Cross- Traffic safety’
is selected...
..
Categories
This warning light informs the driver the following situations.
-- Forward Collision-Avoidance Assist system malfunction (if equipped)
-- Forward Collision-Avoidance Assist radar blocked (if equipped)
-- Blind-Spot Collision Warning system malfunction (if equipped)
-- Blind-Spot Collision Warning radar blocked (if equipped)
-- Lamp malfunction (if equipped)
-- High Beam Assist malfunction (if equipped)
-- Tire Pressure Monitoring System (TPMS) malfunction (if equipped)
read more