Hyundai Venue: Tire Pressure Monitoring System / TPMS Sensor. Repair procedures

Hyundai Venue (QX) (2020-2025) Service Manual / Suspension System / Tire Pressure Monitoring System / TPMS Sensor. Repair procedures

Replacement

1.	Remove the wheel and tire.

2.	Remove the valve core and deflate the tire.

3.	Install the wheel tire to the tire change machine.

4.	Push the tire as the illustration below.

5.	Remove the TPMS sensor by loosening the nut.

Push the TPMS sensor into the valve hole on the rim.

Hyundai Venue. TPMS Sensor. Repair procedures

•	Position sensor housing horizental to the plane of rim well.

•	Position TPMS sensor axis coaxial with rim valve holt axis.

7.	Pre-assemble the nut on the TPMS sensor.

Tighten the TPMS sensor nut.

Tightening torque :

7.0 - 9.0 N.m (0.7 - 0.9 kgf.m, 5.2 - 6.6 lb.ft)

Hyundai Venue. TPMS Sensor. Repair procedures

•	THE TPMS sensor fixing nut must not be reuesed.

•	Must asseble TPMS sensor without inclination in the right or left direction.

•	Gap between TPMS sensor housing and rim must be within 2.5 mm (0.0984 in).

•	TPMS sensor must be safe from harmful impact.

9.	Remove the tire change machine.

10.

Inject air into the tire until the beads are in the correct position.

Tier pressure

17 inch : 2.3 kg/cm (33 psi)

18 ichh : 2.4 kg/cm (35 psi)

Hyundai Venue. TPMS Sensor. Repair procedures

Diagnostic Procedure Using a Diagnostic Instrument

The following section describes how to diagnose faults using a diagnostic instrument.

1.	Connect the diagnostic instrument to the self-diagnostic connector (16-pin) beneath the crash pad on the side of driver's seat, and then turn on the ignition to activate the diagnostic instrument.

2.	In the GDS Vehicle Type Selection menu, select "Vehicle Type" and "TPMS" System, and then opt for "OK."

[Register Sensor Method]

Hyundai Venue. TPMS Sensor. Repair procedures

•	Check that Write ID and Read ID are the match.

•	After successfully registering the sensor, perform "Sensor Wireless Information" to confirm that the sensor operates properly.

Hyundai Venue. TPMS Sensor. Repair procedures

[Sensor Status Method]

Hyundai Venue. TPMS Sensor. Repair procedures

•	Each entry must be checked for normal operation of each sensor.

•	After replacing the tires or sensors, check for proper operation of sensor after sensor registration process.

Hyundai Venue. TPMS Sensor. Repair procedures

TPMS Sensor. Description and operation

Description 1. General description WU is a sensor placed in the tire that reports pressure and temperature. The WU is mounted inside the wheels, fixed to the valve...

TPMS Receiver. Description and operation

Description TPMS Receiver : Integrated Body Control Unit (IBU) integrated management 1. Mode (1) Virgin State • The receiver as a sole part is shipped in this state...

Other information:

Hyundai Venue (QX) (2020-2025) Service Manual: Crash Pad Lower Panel. Repair procedures

Replacement • Put on gloves to prevent hand injuries. • When removing with a flat-tip screwdriver or remover, wrap protective tape around the tools to prevent damage to components...

Hyundai Venue (QX) (2020-2025) Service Manual: TPMS Sensor. Description and operation

Description 1. General description WU is a sensor placed in the tire that reports pressure and temperature. The WU is mounted inside the wheels, fixed to the valve. The angle between the valve and the housing of the WU is variable...

Hyundai Venue: Tire Pressure Monitoring System / TPMS Sensor. Repair procedures

TPMS Sensor. Description and operation

TPMS Receiver. Description and operation

Other information:

Hyundai Venue (QX) (2020-2025) Service Manual: Crash Pad Lower Panel. Repair procedures

Hyundai Venue (QX) (2020-2025) Service Manual: TPMS Sensor. Description and operation

Categories

Instrument Panel Overview