Hyundai Venue: Front Suspension System / Rear Torsion Beam Axle. Repair procedures
[Rear drum brake type]
1. |
Loosen the wheel nuts slightly.
Raise the vehicle, and make sure it is securely supported.
|
2. |
Remove the rear wheel and tire (A) from the rear hub.
Tightening torque :
107.9 - 127.5 N.m (11.0 - 13.0 kgf.m, 79.6 - 94.0 lb-ft)
|
•
|
Be careful not to damage the hub bolts when removing
the rear wheel and tire (A).
|
|

|
3. |
Disconnec the rear wheel speed sensor connector (A).

|
4. |
Loosen the screw and then remove the rear drum brake (A).
Tightening torque :
4.9 - 5.9 N.m (0.5 - 0.6 kgf.m, 3.6 - 4.3 lb-ft)
|

|
5. |
Remove the rear parking cable bracket mounting bolts (A).
Tightening torque :
8.8 - 13.7 N.m (0.9 - 1.4 kgf.m, 6.5 - 10.1 lb-ft)
|

|
6. |
Remove the rear wheel speed sensor bracket mounting nuts (A).
Tightening torque :
8.8 - 13.7 N.m (0.9 - 1.4 kgf.m, 6.5 - 10.1 lb-ft)
|

|
7. |
Remove the rear brake hose bracket mounting bolts (A).
Tightening torque :
12.7 - 16.7 N.m (1.3 - 1.7 kgf.m, 9.4 - 12.3 lb-ft)
|

|
8. |
Loosen the hub mounting bolt and then remove the hub (A) from torsion
beam axle.
Tightening torque :
49.0 - 58.8 N.m (5.0 - 6.0 kgf.m, 36.2 - 43.4 lb-ft)
|

|
9. |
Loosen the bolt and then discoonect the rear shock absorber (A) from
the torsion beam axle.
Tightening torque :
98.1 - 117.7N.m (10.0 - 12.0kgf.m, 72.3 - 86.8lb-ft)
|

|
10. |
Loosen the mounting bolt (A) and then remove the torsion beam axle (B).
Tightening torque :
117.7 - 137.3 N.m (12.0 - 14.0 kgf.m, 86.8 - 101.3 lb-ft)
|


|
[Rear disc brake type]
1. |
Loosen the wheel nuts slightly.
Raise the vehicle, and make sure it is securely supported.
|
2. |
Remove the rear wheel and tire (A) from the rear hub.
Tightening torque :
107.9 - 127.5 N.m (11.0 - 13.0 kgf.m, 79.6 - 94.0 lb-ft)
|
•
|
Be careful not to damage the hub bolts when removing
the rear wheel and tire (A).
|
|

|
3. |
Remove the brake caliper from the torsion beam axle.
(Refer to Brake System - "Rear Disc Brake")
|
4. |
Loosen the bolt & nut and then disconnect the rear shock absorber (A)
from the torsion beam axle.
Tightening torque :
98.1 - 117.7 N.m (10.0 - 12.0 kgf.m, 72.3 - 86.8 lb-ft)
|

|
5. |
Disconnect the rear wheel speed sensor connector (A).

|
6. |
Remove the rear wheel speed sensor bracket mounting nuts (A).
Tightening torque :
8.8 - 13.7 N.m (0.9 - 1.4 kgf.m, 6.5 - 10.1 lb-ft)
|

|
7. |
Remove the rear parking cable bracket mounting bolts (A).
Tightening torque :
19.6 - 29.4 N.m (2.0 - 3.0 kgf.m, 14.5 - 21.7 lb-ft)
|

|
8. |
Loosen the mounting bolt (A) and then remove the torsion beam axle (B).
Tightening torque :
117.7 - 137.3 N.m (12.0 - 14.0 kgf.m, 86.8 - 101.3 lb-ft)
|


|
[Rear torsion beam axle bush replace]
1. |
Remove the rear torsion beam axle from the vehicle.
(Refer to Rear Torsion Beam Axle - "Removal")
|
2. |
Using the SST (09551-AL100) and press, replace the bush (A).

•
|
When press in the bush, press the same direction of
the void (A) and the flange direction (B) before detaching.

|
|
|
1. |
Install in the reverse order of removal.
|
Other information:
Specification
Alternator
Item
Specification
Rated voltage
13.5V, 120A
Speed in use
1,000 - 18,000 rpm
Voltage regulator
IC Regulator built-in type
Regulator Setting Voltage
External mode
Refer to below graph
Internal mode
14...
..
Categories

1. Instrument cluster
2. Horn
3. Key ignition switch/ Engine Start/Stop button
4. Infotainment system
5. Hazard warning flasher switch
read more