Hyundai Venue: indshield Wiper/Washer / Front Wiper Motor. Repair procedures

Hyundai Venue (QX) (2020-2024) Service Manual / Body Electrical System / indshield Wiper/Washer / Front Wiper Motor. Repair procedures

Removal
1.
When replacing the wiper blade, press the blade bottom clip button to remove the blade.

Hyundai Venue. Front Wiper Motor. Repair procedures
2.
Remove the cowl top cover.
(Refer to Body - "Cowl Top Cover")
3.
Remove the windshield wiper motor and linkage assembly (A) after loosening the bolts and disconnecting the wiper motor connector (B).

Hyundai Venue. Front Wiper Motor. Repair procedures
4.
Hold the wiper motor crank arm and remove the upper linkage (A) from the wiper motor crank arm.

Hyundai Venue. Front Wiper Motor. Repair procedures

Hyundai Venue. Front Wiper Motor. Repair procedures   
Before removing the wiper motor and linkage assembly, make sure that the linkage is stoped at auto stop position.
To install the wiper motor crank arm exactly, check that the linkage is aligned with the crank arm in straight line and the angle of each linkages.
Be careful not to bend the linkage.
5.
Remove the lower linkage (A) from the wiper motor crank arm.

Hyundai Venue. Front Wiper Motor. Repair procedures

Hyundai Venue. Front Wiper Motor. Repair procedures   
To install the wiper motor crank arm exactly, check that the linkage is aligned with the crank arm in straight line and the angle of each linkages.
Be careful not to bend the linkage.
6.
Remove the wiper motor from the tube after removing the mounting bolts.

Hyundai Venue. Front Wiper Motor. Repair procedures
Installation
1.
Install the wiper motor.
2.
Install the crank arm.
Hyundai Venue. Front Wiper Motor. Repair procedures   
To install the wiper motor crank arm, make sure that the linkage is aligned with the crank arm in straight line and set the angle of each linkages exactly.
3.
Install the lower and upper linkage to the wiper motor crank arm.
Hyundai Venue. Front Wiper Motor. Repair procedures   
To install the wiper motor crank arm, make sure that the linkage is aligned with the crank arm in straight line and set the angle of each linkages exactly.
Be careful not to bend the linkage.
4.
Install the wiper motor and linkage assembly and then connect the wiper motor connector.
Tightening torque :
6.9 - 10.8 Nm (0.7 - 1.1 kgf.m, 5.0 - 7.9 lbf.ft)
5.
Install the cowl top cover.
6.
Install the windshield wiper arm and blade.
Tightening torque :
22.5 - 26.5 Nm (2.3 - 2.7 kgf.m, 16.6 - 19.5 lbf.ft)
Hyundai Venue. Front Wiper Motor. Repair procedures   
–
The windshield wiper motor must be cycled to make sure that it is in the park position.
If necessary, adjust the wiper arm and blade.
7.
Install the wiper arm and blade to the specified position.
A: Auto stop position (Blade)

Hyundai Venue. Front Wiper Motor. Repair procedures
Inspection
Speed Operation Check
1.
Disconnect the connector (A) from the wiper motor.

Hyundai Venue. Front Wiper Motor. Repair procedures
2.
Check that the motor operates at low or high speed as below table.

Hyundai Venue. Front Wiper Motor. Repair procedures

Hyundai Venue. Front Wiper Motor. Repair procedures   
Common sources of contamination are insects, tree sap, and hot wax treatments used by some commercial car washes. If the blades are not wiping properly, clean both the window and the blades with a good cleaner or mild detergent, and rinse thoroughly with clean water.

    Front Wiper Motor. Components and components location

    Component Location 1. Cap 2. Nut 3. Wiper arm & blade 4. Cowl top cover 5. Bolt 6. Wiper motor & linkage assembly 7...

    Front Washer Motor. Repair procedures

    Inspection Front and Rear Washer Motor 1. With the washer motor connected to the reservoir tank, fill the reservoir tank with water...

    Other information:

    Hyundai Venue (QX) (2020-2024) Service Manual: Repair procedures


    Removal 1. Disconnect the negative (-) battery terminal. 2. Remove the cluster fascia panel. (Refer to Body - "Cluster Fascia Panel") 3. Remove the cluster (A) from the housing after loosening the mounting screws...

    Hyundai Venue (QX) (2020-2024) Service Manual: Description and operation


    Description Heated Oxygen Sensor (HO2S) consists of zirconium and alumina and is installed on upstream and downstream of the Warm up Catalytic Converter (WCC). After it compares oxygen consistency of the atmosphere with the exhaust gas, it transfers the corresponding voltage signal to the ECM...

    Categories

    Instrument Panel Overview

    Hyundai Venue. Instrument Panel Overview

    1. Instrument cluster
    2. Horn
    3. Key ignition switch/ Engine Start/Stop button
    4. Infotainment system
    5. Hazard warning flasher switch

    read more


     
    Copyright © 2024 www.hvenueqx.com